GENERIC USB AUDIO DRIVER LINUX HOW TO
GENERIC USB AUDIO DRIVER LINUX MAC OS X
GENERIC USB AUDIO DRIVER LINUX SOFTWARE
GENERIC USB AUDIO DRIVER LINUX MAC

(Again, if you’re familiar with SSH then you can simply connect and perform the remaining commands remotely).įirst, I’ll make sure that the USB audio device is being detected by both the hardware and software. Power up your Raspberry Pi and, once it has booted, open the LXTerminal app. Remember, if you need access to both USB ports then use the USB audio device in conjunction with a USB extension cable, preventing the second port from being blocked. Step 1īefore continuing, make sure your Raspberry Pi is switched off and then connect the USB audio device to its USB port.

GENERIC USB AUDIO DRIVER LINUX HOW TO

If you’re familiar with SSH and know how to access your Raspberry Pi using it, you can perform the following steps without needing to be physically at your Raspberry Pi. The following steps will be performed within the command line on the Raspberry Pi. Now that I’ve covered the requirements for sourcing a suitable USB audio device, I will show you how to configure it. If you’re needing to use both USB ports at the same time, I would recommend using a USB extension cable and connecting your USB audio device that way, instead. Tip: USB audio devices are usually a little larger than a memory stick and will probably take up more physical space, blocking access to the second USB port. If you’re running your Raspberry Pi from a mains adapter then you should be all set. When using any USB audio device, you’ll need to make sure that your Raspberry Pi is being powered enough that it is able to support a USB-powered device. This particular audio device uses the C-Media audio chipset, something that is supported by AlsaProject in Raspian.

Not bad for something that costs less than a cup of coffee!

GENERIC USB AUDIO DRIVER LINUX MAC

I've previously used this USB audio device with both Mac and PC. The reason for using this particular USB audio device are as follows: It’s called, quite vaguely, the 7.1 Channel USB External Sound Card Audio Adapter.

The USB audio device I will be using with my Raspberry Pi is a generic one I found on Amazon, costing just $2. Tip: Not all USB audio output devices are supported, though you can check the AlsaProject Compatibility List to ensure the device you’re planning to use should be compatible.

GENERIC USB AUDIO DRIVER LINUX MAC OS X

This is applicable not only to Mac OS X and Windows, but also Linux as well, with Raspbian being able to support devices via the AlsaProject, a set of widely compatible audio drivers for Linux.

GENERIC USB AUDIO DRIVER LINUX SOFTWARE

There are certainly a small number of more specialised audio devices that require additional software but any generic audio output device is usually just plug-and-play Compatibility Nowadays, most modern operating systems and audio devices have no such requirements as most chipsets work to an accepted standard, and since most manufacturers will make use of the same small number of chipsets, providing widespread support is far easier. This is what the drivers and software are for and you’ll often find that a number of different audio devices from many manufacturers will use the exact same chipset, the only difference between them will usually just be the branding. The reason for this is that many devices from different manufacturers actually use the same chipset, the physical components that make up the device. This often proved very frustrating for end-users and developers alike. It will be expected that you have completed this tutorial and your Raspberry Pi is currently able to act as an AirPlay receiver, albeit with its built-in audio output.īack in the good old days, most audio devices needed their own set of drivers and software to work. This tutorial will follow on from my previous tutorial, Using a Raspberry Pi as an AirPlay Receiver. We’re not going to squeeze much more out of the built-in components so, in this tutorial, I’ll explain how to set up and configure a cheap USB sound card as the Raspberry Pi’s default audio output device, providing a better quality, and volume, audio. This, however, produces sound that is mediocre at best and if you’re wanting to use the Raspberry Pi for any amount of audio listening, it’s going to have to produce a better quality of audio. My previous tutorial on the Raspberry Pi, Using a Raspberry Pi as an AirPlay Receiver, made use of the device’s built-in 3.5mm jack for audio output.

Generic usb audio driver linux